AVALIAÇÃO DO AÇO ABNT P20 USINADO POR EDM COM SOLUÇÃO AQUOSA DE OCTABORATO DE SÓDIO TETRAHIDRATADO COMO FONTE DE BORO

Autores

  • João Paulo Moreira Santos Barbosa CEFET - MG
  • Anderson Edson da Silva CEFET - MG
  • Sinval Pedroso da Silva IFMG
  • Ernane Rodrigues da Silva CEFET - MG

DOI:

https://doi.org/10.22407/1984-5693.2023.v15.p.e20231501

Resumo

Este trabalho apresenta um estudo da usinagem do aço ABNT P20 realizado em uma máquina de Usinagem por Descargas Elétricas por Penetração (S-EDM) adaptada, utilizando cobre eletrolítico como eletrodo ferramenta e octaborato de sódio tetrahidratado (Na2B8O13.4H2O) como fonte de boro, diluído em água deionizada. As amostras foram preparadas com o uso de técnicas metalográficas para caracterização das camadas refundida e intermediária, que foram formadas após o processo. Para medição da espessura das camadas e verificação de alterações microestruturais e morfológicas, foram obtidas imagens utilizando microscopias óptica e eletrônica de varredura. A dureza das camadas foi medida por meio de ensaios de microdureza Vickers, e a presença de boretos foi verificada por meio de difração de raios X (DRX). Após a realização do processo S-EDM, foi verificado aumento de 112% e 92%, aproximadamente, no valor médio de microdureza Vickers das camadas refundida e intermediária, respectivamente, em relação ao material-base, fato que pode ser justificado pela presença das fases FeB e Fe2B obtidas por DRX.

Referências

BRAKMAN, CM; GOMMERS, AWJ; MITTEMEIJER, EJ. Boriding of Fe and Fe–C, Fe–Cr, and Fe–Ni alloys; boridelayer growth kinetics. Journal of Materials Research, v. 4, n. 6, p. 1354-1370, 1989.

CHAPMAN, B. Glow discharge process – sputtering and plasm etching. New York, John Wiley & Sons, 1980.

DA SILVA, SP; ABRÃO, AM; SILVA ER; CAMARA, MA. Surface modification of AISI H13 steel by die-sinking electrical discharge machining and TiAlN coating: a promising hybrid technique to improve wear resistance. Wear, v. 462, p. 203509, 2020a.

DA SILVA, SP. et al. Investigation of nitride layers deposited on annealed AISI H13 steel by die-sinking electrical discharge machining. The International Journal of Advanced Manufacturing Technology, v. 109, n. 7-8, p. 2325-2336, 2020b.

DOSSETT, JL; TOTTEN, GE. Heat Treating of Irons and Steels. ASM HANDBOOK V. 4, 2014.

GHANEM, F; BRAHAM, C; FITZPATRICK, ME; SIDHOM H. Effect of near-surface residual stress and microstructure modification from machining on the fatigue endurance of a tool steel. Journal of materials engineering and performance, v. 11, p. 631-639, 2002.

GÖK, MS. et al. Dry sliding wear behavior of borided hot-work tool steel at elevated temperatures. Surface and

Coatings Technology, v. 328, p. 54-62, 2017.

KAYALI, Y. Investigation of diffusion kinetics of borided AISI P20 steel in micro-wave furnace. Vacuum 121, 129-134, 2015.

KÖNIG, W. Fertigungsverfahren 3: Abtragen und Generieren. Springer-Verlag, 2013.

KULKA, M. Current trends in boriding. Cham: Springer International Publishing, 2019.

MORÓN, RC. et al. Friction and reciprocating wear behavior of borided AISI H13 steel under dry and lubricated conditions. Journal of Materials Engineering and Performance, v. 29, n. 7, p. 4529-4540, 2020.

NASCIMENTO NETO. ER. Utilização de plasma na Remoção de Óleo da Superfície de Alumínio. Campinas. Dissertação de Mestrado - Faculdade de Engenharia Química, Universidade Estadual de Campinas, 2006.

NOVAKOVA, AA. et al. Electron-beam boriding of low-carbon steel. Journal of alloys and compounds, v. 383, n. 1-2, p. 108-112, 2004.

ÖZERKAN, HB. Simultaneous machining and surface alloying of AISI 1040 steel by electrical discharge machining with boron oxide powders. Journal of Mechanical Science and Technology, v. 32, p. 4357-4364, 2018.

PRAMANIK, A. et al. Fatigue life of machined components. Advances in Manufacturing, v. 5, p. 59-76, 2017.

RASLAN, AA; SILVA, ER; SANTOS, RF. Método de nitretação através da usinagem com descargas elétricas – NDE. Uberlândia, MG, 2012.

RASLAN AA. Implantação Iônica em Meio Aquoso por EDM: Resistência ao Desgaste de Aço AISI 4140. Anais... 8º COBEF -Congresso Brasileiro de Engenharia de Fabricação, Salvador, 2015.

SANTOS, RF. Nitretação por EDM do aço AISI 4140. Tese de Doutorado - Universidade Federal de Uberlândia,

Uberlândia, 2013.

SANTOS, RF; SILVA, ER; SALES, WF; RASLAN, AA. Analysis of the Surface Integrity when Nitriding AISI 4140 Steel by the Sink Electrical Discharge Machining (EDM) process. Procedia CIRP, v. 45, p. 303-306, 2016.

SANTOS, RF; SILVA, ER; SALES, WF; RASLAN, AA. Influence of the electrode material on the nitriding of medium carbon steel using sink electrical discharge machining. The International Journal of Advanced Manufacturing

Technology, v. 90, p. 2001-2007, 2017.

SCHUBERT, DM. Borates in industrial use. Group 13 Chemistry III: Industrial Applications, p. 1-40, 2003.

SHEN, KK. Boron‐Based Flame Retardants in Non‐Halogen Based Polymers. Non‐Halogenated Flame Retardant Handbook, p. 309-336, 2021.

STEVENS, L. Improvement of Surface Quality in Die-sinking EDM. Leuven. Doctorate degree thesis - Departament of Mechanical Engineering. Katholieke Universiteit Leuren. 1998.

TÜRKMEN, I; YALAMAÇ, E. Effect of Alternative Boronizing Mixtures on Boride Layer and Tribological Behaviour of Boronized SAE 1020 Steel. Metals and Materials International, p. 1-15, 2021.

USLU, I. et al. Evaluation of borides formed on AISI P20 steel. Materials and Design 28, 55–61, 2007.

YADAV, V; JAIN, VK; DIXIT, PM. Thermal stresses due to electrical discharge machining. International Journal of Machine Tools & Manufacture, v. 42, n. 8, p. 877-888, 2002.

ZAGONEL, IF. Tratamentos de superfícies de uma liga ferrosa por íons de nitrogênio. Campinas. Tese de Doutorado - Curso de FÍsica, Universidade Estadual de Campinas, 2006.

Downloads

Publicado

03-04-2023

Edição

Seção

ARTIGOS CIENTÍFICOS